Analysis Type Supported
Construction Stage Analysis
  1. Detail Floor by Floor Analysis
  1. Temporary Support Analysis
  1. Time dependent concrete behavior
  1. CEB-FIP, ACI, PCA, AASHTO Standards
Detailed Section Analysis
  1. Section Property Calculator for irregular sections
  • Import Section drawing from AutoCAD
  • Create Composite section with more than 2 parts
  1. Stress for a cross section
  • Capacity Curves (P-M, M-M, 3D) & Capacity Check Ratio as per ACI 318 -11, ACI 318-08, CSA S6-10 and AASHTO LRFD 12
  • Moment-Curvature Curves
Material Nonlinear Analysis
  1. Truss, Plate, Plane stress, Plane strain, Axisymmetric and Solid
  1. Tresca, von Mises, Mohr-Coulomb and Drucker-Prager
  1. Isotropic, kinematic and mixed hardening
  • Lumped hinge & Distributed hinge
  • Automatic calculation of yield strength
  • Axial load – biaxial moment interaction
  • Fiber model Analysis
  1. Pushover Analysis
  • Auto Plastic Hinge Definition
  • Auto PM Interaction curve for hinge formation
  • Obtain Performance point as per FEMA
Soil Structure Interaction
  1. Model Foundation - Footing, Raft and Piled Raft
  1. Define Soil Springs with built in formulae using soil properties for Piles
  1. Obtain Effect of Non Stiff Foundation on Analysis of Superstructure
  1. Settlement Analysis
  • Define Anticipated Settlement on Supports
  • Obtain worst effect due to combination of settlements on different supports
Column Shortening Analysis
  1. Auto Column Shortening
  1. Time Dependent concrete material definition
Wind Analysis
  1. Auto Definition of Wind Static Loads as per IBC, UBC codes
  1. Static / Dynamic Analysis with P Delta effect
Thermal Analysis
  1. Nodal/Element Temperature change analysis
  1. System Temperature change analysis
  1. Differential temperature in the cross section Analysis
  1. Temperature Gradient Analysis
Buckling Analysis
  1. Obtain results for Global buckling and local buckling
Heat of Hydration Analysis for mass concrete
  1. Analysis - Heat Transfer Analysis based on construction stages
  1. Convection, Heat Source, Pipe cooling, etc.
Seismic Analysis
  1. Equivalent Static Seismic Analysis by Auto Definition of Static loads from code
  1. Response Spectrum Analysis considering Damping
  1. Eigenvalue Analysis
  1. Definition of viscoelastic damper, lead rubber bearing isolator etc.
  1. Inelastic Time History Analysis
  • Lumped hinge & Distributed hinge
  • Automatic calculation of yield strength
  • Axial load – biaxial moment interaction
  • Fiber model Analysis
  1. Pushover Analysis
  • Auto Plastic Hinge Definition
  • Auto PM Interaction curve for hinge formation
  • Obtain Performance point as per FEMA
Higher Order Analysis
  1. P Delta Analysis
  1. Geometric Non Linear Analysis
  1. Large Displacement (Forward/Backward) Analysis
  • Suspension Bridge
  • Cable Stayed Bridge
  • Cable Tuning
Geometric Non Linear Analysis
  1. Large Displacement (Forward/Backward) Analysis
  • Suspension Bridge
  • Cable Stayed Bridge
  • Cable Tuning
Element Library
  1. Truss Element
  1. Tension-only Element (Hook function included)
  1. Cable Element
  1. Compression-only Element (Gap function included)
  1. Beam Element/Tapered Beam Element
  1. Plane Stress Element
  1. Plate Element
  1. Two-dimensional Plane Strain Element
  1. Two-dimensional Axisymmetric Element
  1. Solid Element
Type of Supports
Restrain in Translation in X Y Z RX RY and RZ
Elastic Links
  1. General
  1. Compression/Tension only
  1. Multi Linear
Point Spring Supports
  1. General
  1. Compression/Tension only
  1. Multi Linear
Surface Springs
  1. Springs for Flat Footings
General Spring
  1. Stiffness Matrix
  1. Mass Matrix
  1. Damping Matrix
General Link
  1. Viscoelastic Damper
  1. Gap
  1. Hook
  1. Lead Rubber bearing isolator
  1. Friction pendulum isolator
Beam End Release
  1. Fx, Fy, Fz
  1. Mx, My, Mz
Plate End Release
  1. Fx, Fy, Fz
  1. Mx, My, Mz
Linear Constraints
  1. Explicit with respect to any one deformation
  1. Weighted Displacement with respected to combination of deformations
Rigid Link
  1. DX, DY, DZ, RX, RY, RZ
Node Local Axis
Design Supported
  1. Concrete Frame/Brace/Shear Wall Design/Check as per ACI 318-11, ACI 318-08, ACI 318-05, ACI 318-02, ACI 318 -99, ACI 318- 95, ACI 318-89, and CSA A A23 3 94
  1. Steel Frame Check as per AISC 14th LRFD 10, AISC 14th ASD 10, AISC 13th LRFD 05, AISC 13th ASD 05, AISC LRFD 2k, AISC LRFD 93, AISC ASD 89, AISI CFSD86,CSA S16 01.
  1. Strong Column Weak Beam Design as per ACI
  1. Wall Design as per ACI
  1. Slab Design as per ACI
  1. Steel optimal design as per ACI